Special offer of the CNC CMM TETA

Renishaw PH6 rigid probe head with TP200 probe

Rigid probe head PH6 and high-precision measuring probe TP200 for use with star probes and, if required, with the SCR200 probe changing system.

Benefits:

For stylus lengths up to 100 mm

Highest scanning accuracy even with longer stylus

The probe system requires little space

Long service life of the stylus modules of> 10 million touch points / module

Disadvantage:

No swiveling of the probe head

Operation area:

If all features can be recorded with a star stylus and if stylus lengths of up to 100 mm are sufficient

Suitable for the following applications:

The highest precision to be measured is approx. 0.012 mm

A lateral immersion depth of 50 mm is sufficient

The immersion depth of 100 mm in the Z direction is sufficient

Inclined holes outside the 3 main directions (X, Y, Z) are the exception or do not occur

More commonly used for small CNC measuring machines, as the probe system is very space-saving

Simple Renishaw RTP20 automatic turn-swivel head

Can be adjusted in 15 ° steps by moving the machine. Reproducibility 1.5 µm with a swivel radius of approx. 70 mm.

Benefits:

Inexpensive

Fully automatable

Small swivel radius

Compact design

An automatic stylus changer including 2 stylus modules is already included in the price

Disadvantage:

Can only be pivoted automatically with the aid of an anchor rod

This must be in the measuring volume and thus consumes the measuring volume

The panning process is slow and takes about 10 seconds

The angular resolution of the two swivel axes is only 15 ° and is therefore relatively low

The stylus length is limited to 60 mm

The TP20 push button modules are relatively expensive at around € 890 / module

The service life of the modules is around 3 million. Touch points relatively low

Operation area:

If the probe head does not need to be rotated and swiveled too often and probe lengths of up to 60 mm are sufficient

Suitable for the following applications:

Swivel steps of 15 ° are sufficient

The duration of the measurement is not critical

The immersion depth of 60 mm is sufficient

More commonly used for small CNC measuring machines

Button pans are not that common

Prices for the TETA coordinate measuring machine with the RTP20 & PH6

PH10T motorized rotary swivel head from Renishaw for CNC-controlled swiveling of the probe head in 7.5 ° steps and TP20 probe.

Pivots motorized in 2 axes in 7.5 ° steps (max. 720 positions). A position feedback is sent to the control. The reproducibility of the swivel position +/- 0.5 µm with a swivel radius of around 100 mm. Max. Length of the extension of the probe 300 mm. Max. Length of the stylus 60mm.

Benefits:

Fast swiveling of the probe head

Höhere Schwenkgenauigkeit von +/-0.5 µm bei etwa 100 mm Schwenkradius

Higher swivel accuracy of +/- 0.5 µm with a swivel radius of around 100 mm

Greater process security through CNC-controlled swiveling

Finer resolution of the swivel angle (720 swivel positions)

Fully automatable

Relatively small swivel radius

Disadvantage:

The PH10T probe head is significantly more expensive (approx. € 7,000 more expensive) than the RTP20 probe head

The stylus length is limited to 60 mm

The TP20 stylus modules are relatively expensive at around € 900 / module

Touch points relatively low

Operation area:

Automated measuring machines with high reliability, as the probe head is CNC controlled

Shorter measuring times by swiveling the probe head quickly

Stylus lengths of up to 60 mm are sufficient

Suitable for the following applications:

The highest precision to be measured is approx. 0.014 mm

The duration of the measurement plays a medium role

The immersion depth of 60 mm is sufficient

Swivel steps of 7.5 ° are sufficient

PH10T motorized swivel head from Renishaw for CNC-controlled swiveling of the probe head in 7.5 ° steps and TP200 probe for probe lengths up to 100 mm with high probing accuracy.

Pivots motorized in 2 axes in 7.5 ° steps (max. 720 positions). The header position is reported to the control. The reproducibility of the swivel position +/- 0.5 µm with a swivel radius of around 100 mm. Max. Length of the extension of the probe 300 mm. Max. Length of the stylus 100 mm.

Benefits:

Fast swiveling of the probe head

Higher swivel accuracy of +/- 0.5 µm with a swivel radius of around 100 mm

An automatic stylus changer including 3 stylus modules is already included in the price

Greater process security through CNC-controlled swiveling. Finer resolution of the swivel angle (720 swivel positions)

Stylus lengths up to 100 mm

High scanning accuracy even with longer stylus

The price for a stylus module is around € 550, significantly cheaper than the TP20 modules at around € 900

Fully automatable. Relatively small swivel radius.

Disadvantage:

The PH10T is significantly more expensive (approx. € 7,000 more expensive) than the RTP20

Operation area:

Automated measuring machines with high reliability as the probe head is CNC controlled

Shorter measuring times by swiveling the probe head quickly

Stylus lengths up to 100 mm. High scanning accuracy even with longer stylus

3 times longer service life of the TP200 stylus modules compared to the TP20

Suitable for the following applications:

The highest precision to be measured is approx. 0.012 mm

The duration of the measurement plays a medium role

The immersion depth of 100 mm is sufficient

High probing accuracy even with longer styli up to 100 mm

Long service life of the stylus modules of over 10 million probes required

Swivel steps of 7.5 ° are sufficient

Prices for the TETA coordinate measuring machine with the Renishaw PH10T probe head

PH20 5-axis probe head swivels to any angle in space

Can control any angle in the room. The resolution of the angular positions is 0.15 sec. When measuring circles, the head-touch function can be used. This means that the probing speed is up to 5 times higher than with conventional machine movements.

Benefits:

Any angle in the room can be controlled

The head-touch function can be used when measuring circles. As a result, the speed of probing is up to 5 times higher than with conventional machine movements

The probe head can be swiveled simultaneously with the machine movement

Small swivel radius

Compact design

Disadvantage:

The stylus length is limited to 60 mm

If the stylus is long, the head-touch speed and the scanning accuracy are reduced

The head-touch function can only be used to a limited extent in the X-Y plane

Operation area:

Ideally suited for workpieces with bores in any spatial angle

Preferred for measuring bores, as this is where the head-touch function can best be used

Suitable for the following applications:

The highest precision to be measured is approx. 0.014 mm

A short measurement time is important

An immersion depth of 60 mm is sufficient

Any angle must be able to be set, since many inclined holes have to be measured

Prices for the TETA coordinate measuring machine with the Renishaw probe head PH20

PH10M motorized rotary swivel head from Renishaw for CNC-controlled swiveling of the probe head in 7.5 ° steps

Pivots motorized in 2 axes in 7.5 ° steps (max. 720 positions). A position feedback is sent to the control. The reproducibility of the swivel position +/- 0.5 µm with a swivel radius of around 100 mm. Max. Stylus length 400 mm.

Benefits:

Continuous scanning of the geometry

Measure high point densities in a short time

This makes it ideal for shape measurements (circular shape, cylinder shape, flatness, straightness, etc.)

Disadvantage:

High demands on the cleanliness of the workpieces, increased wear on the stylus

Rougher surfaces can cause the stylus to vibrate

Due to the longer design of the scanning button, more measuring path is required on the measuring machine

Operation area:

For shape measurements

Measure elements with a high point density in a short time

If stylus lengths greater than 100 mm are required

Suitable for the following applications:

The highest precision to be measured is approx. 0.010 mm

The measurement duration should be as short as possible for a high throughput

An immersion depth of up to 400 mm is possible

Swivel steps of 7.5 ° are sufficient

Prices for the TETA coordinate measuring machine with the Renishaw probe head PH10M